HAND CASE NECK TURNER & CASE HOLDER

_____________________________

HAND CASE

NECK TURNER

& CASE HOLDER

PRODUCT INSTRUCTIONS

SAFETY

Reloading is an enjoyable and rewarding hobby that is easily conducted with

safety. But carelessness or negligence can make reloading hazardous. This

product has been designed from the beginning with the user’s safety in mind.

As with any reloading operation, safety rules must be followed. By observing

these few rules, the chance of hazardous occurrence causing damage or injury

becomes extremely remote.

GENERAL

• Use the equipment as the manufacturer recommends. Study the instructions

carefully and become thoroughly familiar with the operation of the product.

Don’t take short cuts.

• Observe “good housekeeping” in the work area. Keep tools and

components neat, clean and orderly. Promptly clean up any powder spills.

• Always wear adequate eye protection.

• If any unusual resistance is encountered when moving the operating handle,

STOP IMMEDIATELY and investigate the cause. To proceed against

unusual resistance may damage equipment and/or cause serious injury!

LOADING DATA

• Use only laboratory tested data. We highly recommend the use of the

SPEER Reloading Manual.

• OBSERVE ALL WARNINGS ABOUT THE USE OF MAXIMUM

LISTED LOADS.

POWDER HANDLING

• WARNING: Primers are designed to explode and will do so when subjected

to heat or percussion.

• Do not decap live primers!

• Never attempt to seat or reseat a primer in a loaded cartridge.

• Store primers and powder beyond the reach of children and away from heat,

dampness, open flames and electrical equipment.

• DO NOT use any powder unless its identity is positively known. Discard

all mixed powders and those of uncertain or unknown identity.

• Before charging cases, settle the powder in the powder hopper. Throw and

check the weight of at least ten charges. This will assure you that the

correct powder charge is being thrown.

• After a reloading session ends, return the remaining powder back into its

original factory container. This will preserve the identity and shelf life of

the powder.

• DO NOT SMOKE while handling powder or primers.

RECORD KEEPING

• Keep complete records of reloads. Apply a descriptive label to each box

showing the date produced, and the primer, powder and bullet used. Labels

for this purpose are packed with SPEER bullets.

Since RCBS has no control over the choice of components, the manner in

which they are assembled, the use of this product, or the firearms in which

the resulting ammunition may be used, no responsibility, either expressed

or implied, is assumed for the use of ammunition reloaded with this tool.

GENERAL INFORMATION

The Hand Case Neck Turner and Case Holder from RCBS is the most

convenient case neck turning tool you can get your hands on. The neck turning

tool features the ability to ‘zero’ the cutter to the pilot/mandrel, allowing for the

precise case neck thickness to be dialed in for the cut. The micrometer cutter is

graduated in adjustments of .0005” and can be locked in place once the desired

setting is achieved. The pilot/mandrel (sold separately) is designed so that you

can set it as a case mouth stop insuring uniformity over the length of the cut.

The unique 2” diameter Case Holder is comfortable to use and quick to change

cases. The small collet will fit cases from .22 Hornet to 7.63X54R. The large

collet will fit cases from .308 Winchester/.30-06 Springfield to Weatherby

Magnum/Lapua Magnum. The case guide plug helps to center the case and

expose a consistent amount of the case neck and shoulder. Cases can also be

held exposing the base of the case for preparation of the primer pocket on the

Trim Mate Case Prep Center (sold separately).

Unpack the Hand Case Neck Turner Tool carefully. Look for and identify the

following items:

• Hand Case Neck Turner Body

• Part bag #1 with the following parts: Micrometer assembly and Spring

• Part bag#2 with the following parts: Brass lock ring, cutter, hex wrench,

10/32x3/16” and 10/32x3/8” set screws

• Case Holder Body

• Case Holder Cap

• Case Holder Lock Nut

• Case Holder Guide Plug

• Case Holder Collet – Large

• Case Holder Collet – Small

• Case Holder Guide Plug “O”Rings(2)

ASSEMBLY

Hand Case Neck Turner(HCNT)

Open part bags #1 and #2 and lay out pieces in an orderly fashion. Thread the

brass lock ring about ¾ of the way up onto the threads of the micrometer body.

Slide cutter spring over the cutter shaft and insert into bottom of Micrometer

Body. Carefully thread the Micrometer Assembly about half way into the cutter

shaft hole(see photo 1) Continue threading the micrometer assembly in until

about 1/4” of the cutter is exposed. Rotate until the flat part of the cutter is

facing “up”. (see photo 1). Install the 3/8” long socket head set screws(SHSS)

into the body until it just touches the flat part of the cutter shaft(see photo 2).

The cutter should still be able to slide in and out. Slide the appropriate

pilot/mandrel(sold separately) into the tool body and secure with the 3/16”

SHSS. The pilot/mandrel should be secured so that the larger diameter stop

portion does not interfere with the cutter.

Photo 1 Photo 2

Case Holder

First you must determine the body diameter of the cases you are turning. Cases

with body diameters between .22 Hornet and 7.62x54R should use the 5

fingered Small collet. Cases from .30-06 to WBY Mag diameter should use the

6 fingered Large collet. Insert the appropriate collet into the bottom of the case

holder and secure with the lock nut (see photo 3). Install two rubber “O” rings

onto the guide plug and install guide plug assembly into the bottom of the

locknut with the cupped end in towards the collet(see photo 4). Thread the cap

onto the holder.

Photo 3 Photo 4

CASE PREPARATION

Cases must be sized, trimmed for Over-All Length(OAL) and the case mouths

chamfered and deburred for use with the HCNT. Remove case lubricant from

cases. The Case Holder will not be as effective if cases still have case lubricant

on them.

TO USE

The Hand Case Neck Turner is designed so that the case is rotated around the

pilot/mandrel though you can choose to rotate the cutter assembly around the

case. The assembly instruction above is for holding the HCNT in your left hand

and rotating the case, in a clockwise direction with your right hand. You can

change the tool for left handed operation by removing the cutter SHSS, rotating

the cutter 180 degrees and reinstalling the SHSS into the other side. Rotation

then would be counter clockwise.

With the proper pilot/mandrel installed(sold separately), temporarily lock into

place with the SHSS. To set the length of the cut, slide a sized, trimmed for

OAL and chamfered case onto the pilot/mandrel up to the stop. Bring the cutter

assembly down until the cutter is just shy of contacting the case neck. Loosen

the pilot/mandrel SHSS and adjust the pilot/mandrel in or out until the leading

edge of the cutter is at the desired point on the case neck/shoulder junction (see

photo 5). Lock the pilot/mandrel SHSS.

Photo 5 Photo 6

Remove the case from the pilot/mandrel. Set the micrometer to 0-0(see photo 6).

Screw the micrometer body down until the cutter contacts the pilot/mandrel and

lock the micrometer body in place with the brass lock ring.

Adjust the micrometer to the desired thickness of the cut. This thickness can be

determined in two ways.

Using a ball (tube) micrometer, measure the case neck thickness at various

points around the neck. Measure at least 5-10 cases in the lot of brass to be

reloaded. The smallest measurement would be what you want to set the cutter

for to have uniform case neck thickness for the entire lot of brass cases.

Another way is to measure the loaded diameter of a cartridge. We will use 6mm

as an example. Using an outside micrometer, if the loaded diameter is .269,

subtract .243 for the bullet diameter leaving you with .026”. Divide that in half

and that would give you a case neck thickness of .013”.

Lock the cutter with the SHSS. It is recommended that if more than .001” of the

case neck is to be cut away or ‘peeled’, two or more passes are made only

cutting .001” of the neck or less.

Case neck brass will be cut or “peeled” on the forward and back motion over the

cutter. Do not cut to the base of the neck and then just pull the case off of the

cutter. Continue to rotate the case as you back down off of the pilot shaft. See

photo below of neck being “peeled” and a properly turned case neck.

The Case Holder is designed to allow you to quickly insert and remove cases.

The design also allows you to rotate the case and put forward pressure to

advance the case neck to the cutter.

The Guide Plug in the base of the Case Holder helps to center the case and

provide a reference so that a uniform amount of the case is exposed.

Loosen the cap enough to allow a case to pass through the collet fingers. Tighten

the cap to secure the case. Guide case neck over pilot/mandrel and begin cutting

or ‘peeling’ the case neck.

Do not hold cases near the shoulder or case mouth, the clamping force of the

case holder could damage thinner walled cases.

PRECISIONEERED RELOADING EQUIPMENT

We think that we make the very best reloading equipment in the world.

If you agree, please tell your friends.

If you disagree, tell us - we want to do something about it!

Customer Service

1-800-533-5000 (US or Canada) or 530-533-5191

Hours: Monday - Thursday, 6:30am - 3:00pm Pacific Time

(hours may vary)

e-mail: rcbs.tech@atk.com or visit our website at www.rcbs.com

RCBS, 605 Oro Dam Blvd., Oroville, CA 95965

CCI - SPEER - RCBS

OUTERS - RAMLINE - ORBEX - FEDERAL

7200542