User manual

http://www.emc2000.co.kr

CE TEST REPORT

Report No.: EMC-FCC-R0065

EMC compliance Ltd.

480-5 SHIN-DONG, YEONGTONG-GU, SUWON-CITY, GYEONGGI-DO, KOREA 443-390

82 31 336 9919 (Main) 0505 299 8311 (Fax)

This test report shall not be reproduced except in full, Without the written approval.

Appendix 6.

User manual

SAMSUNG SMARTCAM

User Manual

SNH-1011N

SPECIFY SERVICE INSTRUCTIONS AND WARRANTY TERMS

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) this device may not cause

harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

FCC NOTE:

THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE

CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT.

SUCH MODIFICATIONS COULD VOID THE USER'S AUTHORITY TO OPERATE THE

EQUIPMENT.

Instructions & Warranty

The manufacturer is not responsible for any loss or radio/TV interference caused by

unauthorized modification of the product.

Such modification will void the warranty of the product as well as the user’s right of use.

WARNING

• The product must be assembled and installed by an adult.

• Before using, read all instructions on this manual thoroughly and follow operational

instructions, warnings on this manual and printed on the product.

• To avoid entangled power cord, do not place it around the baby bed or other infant

furniture. Keep this product and its power cord out of children’s reach.

• Especially, the power cord should be installed carefully while keeping it out of

children’s reach.

• Never use the product near bath tub, sink, washing machine and in wet basement to

avoid moisture.

• The product is designed for indoor use.

• The product is not designed for medical monitoring, and requires a grown-up’s

protective supervision on its use.

• To avoid overheating of the product, do not expose the product to direct sunlight; do

not install or use near a heat source such as heater, radiator, cooking devices (ex:

electric stove or oven) and other warming devices (ex: audio amplifier, TV, etc.).

• Make sure to keep ventilated while using the product.

Avoid pillar or furniture that may block ventilation, when installing the product.

Trademark

is the registered logo of Samsung Techwin Co., Ltd.

The name of this product is the registered trademark of Samsung Techwin Co., Ltd.

Other trademarks mentioned in this manual are the registered trademark of their

respective company.

Restriction

Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no

circumstances, this document shall be reproduced, distributed or changed, partially or

wholly, without formal authorization of Samsung Techwin.

Disclaimer

Samsung Techwin makes the best to verify the integrity and correctness of the contents

in this document, but no formal guarantee shall be provided. Use of this document

and the subsequent results shall be entirely on the user’s own responsibility. Samsung

Techwin reserves the right to change the contents of this document without prior notice.

Samsung SmartCam

User Manual

• Make sure to use the power adaptor provided. If used with unidentified adaptor, it

may damage the product. The power adaptor must be used with regular household

electric supply.

• Avoid sharp, pointed objects around the adaptor’s cable, not to damage the cable.

• Be warned and never hold the cable’s stripped part when connecting / disconnecting

the adaptor to/from the wall outlet.

• To avoid entangled cable lines, avoid using cable extension for adaptor’s power cord.

• The product’s servicing is allowed only to authorized Samsung Techwin’s service

personnel.

• When using the product for children’s care, be careful to keep the product out of

children’s reach.

• The product partially contains component which might cause respiration difficulty.

Accessories and small parts of the product should be stored keeping out of children’s

reach.

• The product is not designed to replace responsibility of human supervision on

children.

• The product is not equipped with device of immediate notification to adult with

accidental/sudden children‘s move; it requires periodic checks and human

supervision.

Contents

GETTING STARTED

Features ……………………………………………………… 4

Getting to know your Monitoring system …………………… 6

INSTALLATION & NETWORK CONNECTION

Installation …………………………………………………… 8

Network Connection and Settings …………………………… 10

MONITORING

Settings ……………………………………………………… 13

Live Video Setup …………………………………………… 23

Admin ………………………………………………………… 25

APPENDIX

Specifications ………………………………………………… 27

Troubleshooting

· English

Features 4

What’s Included 5

Getting to know your Monitoring

system 6

Power Supply 7

Network connection 7

GettinG Started

• Easy to install

- With the help of WPS (Wi-Fi Protected Setup), wireless sharing and easy

connection are enabled.

- Simply visit the home page (www.samsungsmartcam.com) and download and

install the program without a separate installer program.

• Remote monitoring

- Whenever and wherever if you are in the Internet enabled environment, remote

monitoring is ready for you.

- PC, laptop or smart phone can be used for monitoring.

• Real-time alarm

- Detect motion and sound before outputting the alarm in real time via Google Talk

Messenger or with smart phone.

• Cloud Storage

- Upload the event video and images to the user’s YouTube (video) or Picasa

(images) account automatically.

- Anytime anywhere you can enjoy the video and images stored in the cloud

storage.

• Two-way Audio

- With the built-in speakers and microphone, you can make Two-way

communications.

However, it is available only with the smart phone. (Not applicable to the PC or

laptop computer.)

• SNS (Social Networking Service) Alarm supported

- Provide the event alarm (message, video, image) via YouTube, Picasa or Twitter.

- Share special video footage and images with your friends.

• IR Flash

- In a low contrast scene, you can use IR Flash for the monitoring purpose.

Features

Getting Started

What’s Included

The system comes with the following components:

Power Adaptor Quick Guide Warranty Card

Camera & Bracket body Bracket wall Tape wall hanging Network Cable

Check for above components when opening the product package.

· English

Getting to know your Monitoring system

High quality camera lens

Built-in IR LEDs for night vision

Power / Wi-Fi status LED

Built-in Mic

DC IN 5V

SAMSUNG SMARTCAM

NETWORK

DC 5V Power Input

Press to access the receiver menu.

Press the button again to exit.

Network port

Used if WPS is not supported on the Wireless Access

Point or if you do not have a Wireless Access Point

Built-in speaker

스마트폰에서 전달되는 음성을 출력합니다.

Privacy button

Press once to stop transmitting video/audio

Press and hold for 5sec to reset the camera to default

settings

WPS button

Used to pairing the camera with the Wireless Access

Point

Getting Started

Power Supply

Plug-in the camera power adapter to the wall outlet and connect the camera as

shown.

` Make sure to use the provided power adaptor. Otherwise, the product may not operate

properly.

` It will take about 1min for the camera to boot-up completely.

` When the boot-up is complete, the power LED color will change from red to blue.

Network connection

제공된 Network Cable 과 카메라 뒷면의 NETWORK 단자를 연결하세요.

자세한 네트워크 설정 방법은 "Network Connection and Settings"을

참고하세요. (10쪽)

LED status

LED 색상은 동작 상태에 따라 달라집니다.

다음 표를 참고하세요.

색상 상태

Red

Booting 중

Red Blinking

Booting 완료 / Alarm 발생

Green

Server 연결 완료 / 정상 동작 중

Blue Blinking

WPS Pairing 중(0.5초) / Network Setting 중(1초)

Blue

Network 연결 완료

Yellow

Privacy로 설정되어 있는 중

Magenta

Firmware 업데이트 중

DC IN 5V

NETWORK

SAMSUNG SMARTCAM

UNLOCK

LOCK

· English

Installation 8

Precautions 8

Wall mounting 9

Stand mounting 10

Network Connection and Settings 11

Precautions 11

If using a cable router 12

If using a Wireless Access Point not equipping WPS 12

To connect to a wireless network with WPS 13

inStallation &

network ConneCtion

Precautions

1. Install the camera in a place where it can receive the video signal with no

interference.

2. Keep it away from humidity such as around the humidifier.

3. Keep it away from the direct sunlight, strong light or dust; install it in a place

of clear view.

4. Do not install it in a place interrupted by an obstacle.

5. Keep the lens clean at all times.

Wipe it off of dust with a soft cloth.

Installation

Installation & Network Connection

Wall mounting

조립하기

1. Zipper bag에서 Tape wall hanging 및 Bracket wall을 꺼내세요.

2. Tape wall hanging의 사각형 바닥면

필름을 제거한 후, Bracket wall의

바닥면에 위치를 맞춰 부착하세요.

3. Tape wall hanging의 손잡이를 잡고 이형지를 제거한 후, 부착하고자

하는 면의 [▲ Top] 표시가 12시 방향을 향하게 하여 부착하세요.

The Tape wall hanging cannot be reused after being used

once.

부착면에 먼지 / 물기 / 기름기를 사전에 닦아낸 후 부착해야

접착력이 좋습니다.

4. 동봉된 Adaptor의 선을 Bracket wall의

홈에 끼우세요.

Adaptor 플러그 부분이 12시

방향을 향하도록 하세요.

5. Bracket body의 두 개의 홈에 맞춰 선을 정리하세요.

Bracket body의 [UNLOCK LOCK] 표시와 Bracket wall의

[

▲

Top] 각인 방향이 동일한 방향을 향하게 하세요.

6. Bracket body를 시계 방향으로 ‘딸깍’ 소리가 들릴 때까지 회전시켜

고정하세요.

TOPTOP

TOP

UNLOCK

LOCK

UNLOCK

LOCK

UNLOCK

LOCK

Bracket

body의홈

· English

Adaptor의 플러그와 카메라 뒷면의 전원

단자와 연결하세요

` When done, remove the protective film from

the lens.

8. Adjust the camera’s shooting angle as

appropriate.

` Do not put excessive force. Otherwise, it may

cause damage to the camera.

분리하기

1. 카메라 뒷면의 전원 단자에서 Adaptor의 플러그를 빼세요.

2. Bracket body의 왼쪽에 있는 [PUSHI TO RELEASE] 를 누른 상태에서

시계 반대방향으로 돌리면, Bracket wall이 분리됩니다.

[PUSHI TO RELEASE] 를 누르지 않고 Bracket body를 시계

반대방향으로 돌려도 됩니다.

Stand mounting

조립하기

1. Bracket body와 Bracket wall의 [▼], [▲] 각인 방향에 맞춰 조립하세요.

DC IN 5V

NETWORK

SAMSUNG SMARTCAM

UNLOCK LOCK

UNLOCK

LOCK

Installation & Network Connection

2. Bracket wall의 홈을 이용하여 시계 방향으로 ‘딸깍’ 소리가 들릴 때까지

회전시키세요.

3. 분리 시, Bracket body 측면의 [PUSHI TO RELEASE] 를 누른 상태에서

홈을 이용하여 시계 반대방향으로 회전시키세요.

조립 및 분리 시, 손톱이 부러지지 않도록 주의하세요.

4. Adaptor의 플러그와 카메라 뒷면의 전원 단자와 연결하세요.

Precautions

• The wireless network access may fail, depending on the communications

environment.

• For details about the network settings and password, contact your network

administrator or service provider.

• For a specific Internet service requiring user authentication, you may not access

the service. If this is the case, contact the service provider.

• Do not access the unauthorized network.

• The farther the distance from the Wireless Access Point, the longer time the

network connection may take.

• If you fail to access the selected wireless network, try a different Wireless

Access Point to make access.

• For more information about the router or the wireless connection, refer to the

documentation of the router or contact the router manufacturer.

• If the camera is connected to a multiple-Wireless Access Point network

environment, some video packets may be lost, depending on the network traffic

load.

• According to the network policy (blocking UDP) of the service provider, the video

transmission can be limited to one minute.

• In addition to the above two situations, you may encounter a network delay or

interruption due to the network conditions.

• This product has gone through the compatibility test with worldwide top ranking

routers in the market but you may still have a problem in compatibility with some

conventional routers or other routers manufactured by other than the industry

leading companies.

Network Connection and Settings

DC IN 5V

NETWORK

SAMSUNG SMARTCAM

UNLOCK

LOCK

· English

If using a cable router

If you do not have a Wireless Access Point, you must connect the camera using

LAN cable directly to your home router.

1. Connect the network cable to the camera and to the home router as shown

below . Please refer to <Wired Network> on page 24.

DC IN 5V

SAMSUNG SMARTCAM

NETWORK

Internet Service

<Modem>

<Hub>

If using a Wireless Access Point not equipping WPS

If you want to connect the camera using a non-WPS Wireless Access Point,

change the network setting to Wire and try the wireless network.

1. Use the network cable (LAN cable) to connect the LAN port of the unit to the

LAN port of the Wireless Access Point.

2. Register and select the camera according to guide of 03. Monitoring.

3. Set your wireless network environment using the guideline <Wireless

Network> on page 24.

` When the wireless network settings are completed, remove the LAN cable.

` If you fail to connect to the Internet service, contact the service provider for details.

DC IN 5V

SAMSUNG SMARTCAM

NETWORK

Internet Service

<Modem>

Installation & Network Connection

To connect to a wireless network with WPS

What is WPS?

WPS enables to make connection between the camera and the Wireless Access

Point with a simple click of the button.

1. When you apply the power, the power status LED is lit red, and it will change

to red blinking when the booting is completed.

2. Press the WPS button on the camera.

Press the WPS button on the Wireless Access Point within 2min.

3. The WiFi status LED will become steady blue once the camera is connected

to the Wireless Access Point. (may take up to 30sec).

If the Wi-Fi status LED (blue) is not lit, repeat steps 2 through the end and

check it again.

4. The Wi-Fi status LED will became steady green once the camera is

connected to server.

` If the Wireless Access Point do not support WPS or you do not have wirelss router,

please go to Wired Connection.

` If no WPS button is displayed or visible on the display, see the Wireless Access Point’s

manual or contact the manufacturer of your Wireless Access Point for technical

assistance.

` On some routers, you may need to log in to the web interface and click on an

on-screen button to activate the WPS feature.

` If you fail to connect to the Internet service, contact the service provider for details.

DC IN 5V

SAMSUNG SMARTCAM

NETWORK

SAMSUNG SMARTCAM

NETWORK

WPS Button

<Modem>

Internet Service

Wi-Fi

Indicator LED

· English

Settings 14

Account Setup and Registering the Camera 14

Live Video 20

Alarm Settings 21

Live Video Setup 24

Video Setting 24

Network Setting 25

Time Setting 26

Admin 26

Private Key 26

Update Firmware 27

My Account 27

MonitorinG

Account Setup and Registering the Camera

Once you register the product with the site, you can monitor the camera video on

the PC or laptop computer.

Web browser requirements

Windows Mac

- Windows 7, XP supported

- Internet Explorer 7 or 8

(The 64-bit Internet Explorer 8 is not

supported.)

- Firefox

- Chrome

- Safari

- Firefox

- Chrome

` If you fail to make network connection with MAC Safari, follow the instructions below:

1) Click to run the Finder.

2) Click the application, and double-click the Utilities icon.

3) Double-click on the Java Preferences icon.

4) When the Java installer screen appears, click Install.

5) When the installation is completed, check the option of “Enable Web Start and

applet plug-in applications” from the Java preference window.

Settings

Monitoring

1. Enter www.samsungsmartcam.com on the web browser’s address field.

` If you do not have Java installed on your computer, you will be asked to click on the

link to download the Java plug-in and install. This process may take up to 10 minutes

depending on your internet connection speed.

` This product is designed to automatically install JAVA but, in many situations, if it is not

installed automatically, visit by www.java.com and follow the onscreen instructions to

install the product.

Java-uninstalled PC

1) Verify the Java version

• In the SmartCam Web service access page, make search for JAVA

Runtime Environment (hereinafter “JRE”) and check if your PC has installed

the recommended version of JRE 1.6.10 or later. If not, install the latest

version of JRE as recommended by the Company.

2) Move to the Verify Java page

• If you agree to upgrade the current Java version for a PC installing JRE

version 1.6.10 or earlier or a PC not installing JRE yet, you will move to the

Java Verify page.

• If you have not installed Java yet, you will be prompted to install JRE with

a message.

3) Start installing Java

· English

• If you accept the installation of JRE, the installation process will start.

4) Verify Certificate

• When JRE is installed completely, you will move to the SmartCam Web

page. And, you will be prompted to agree to run the application published

by Samsung Techwin Co., Ltd.

5) Start the SmartCam Web service

PC having JRE 1.6 or earlier installed

1) Verify the Java version

• In the SmartCam Web service access page, make search for JAVA

Runtime Environment (hereinafter “JRE”) and check if your PC has installed

the recommended version of JRE 1.6.10 or later. If not, install the latest

version of JRE as recommended by the Company.

• From the Verify Java page, click on the given button to check the Java

version.

2) Verifying the Java version

•

Search for

the

current version of JRE on the PC

3) Check the JRE version of the current PC

•

Check the current JRE version and download the latest version if necessary

( version 7 Update 4 as of 2012/05)

Monitoring

4) Agree to install JRE

•

Agree to install the latest version of JRE

5) Move to the Verify Java page

• If you agree to upgrade the current Java version for a PC installing JRE

version 1.6.10 or earlier or a PC not installing JRE, you will move to the

Java Verify page.

•

If you have not installed Java yet, you will be prompted to install JRE with a

message.

6) Start installing Java

• If you accept the installation of JRE, the installation process will start.

· English

Select <Sign Up> to register.

After reading the terms of use, check on “I agree with”, and click <Next>.

3. Provide the requested information, and click <Sign Up>.

• ID : Enter the user ID and perform the duplicate check.

Fill in the user ID in 8 ~ 12 alphanumeric characters.

• Password : For security reason, provide the user password in 8 ~ 12

alphanumeric characters.

• Confirm Password : Please enter the password again for confirmation.

• Name : Enter the user name.

• E-mail : Enter the correct email address as it is used for reference in case

you forgot the user ID or password.

• Nation : Please select your country.

7) Verify Certificate

• Move to the SmartCam Web page (www.samsungsmartcam.com), and

you will be prompted to agree to run the application published by

Samsung Techwin Co., Ltd.

8) Start the SmartCam Web service

Monitoring

4. Enter the <Serial No> and click the check.

5. Create a <Private key>.

` Private key is required to prevent unauthorized access to the camera.

` You can use one to eight length strings of letters, numbers, and characters except ‘-’

and ‘,’.

6. Create a <Camera Name>.

• Camera Name : You can provide the camera name to your preference for

identification in the multi-camera network. (ex: Living room, Kitchen...)

` You can use one to fifteen length string of letters, numbers, and characters

‘~`!@#$%^&*()_-|{}[];’,./?’.

7. When done, click <Registration>.

` If you want to change the private Key, please refer to <Admin> on page 25.

8. Once the camera is successfully registered, you can check the camera in the

<Camera List>.

SAMSUNG SMARTCAM

MODEL : SNH-1011N

DC 5. OV 2. 2A

M/C : SNH-1011N/US PV

Apr 2012 S/N : XXXXXXXXXXXXXXX

MAC ADDRESS. : XX-XX-XX-XX-XX-XX

SAMSUNG TECHWIN CO., LTD.

MADE BY SAMSUNG IN CHINA

XXXXXXXXXXXXXXX

· English

Live Video

From the <Camera List>, select the camera to monitor and click < >.

` The < > icon indicates the camera is inactive so you cannot monitor it right now.

2. Enter the Private Key and select preferred language.

3. When done, click <OK>.

4. Select <Video>  <Live> to display the live feed from the selected camera.

• <

> : Select frame rate based on your network speed.

Profile Name Resolution Frame rate

Recommended

bandwidth

Low Speed Network VGA 5 fps 768Kbps

Mid Speed Network VGA 10 fps 1Mbps

High Speed Network VGA 30 fps 1.5Mbps

` If the bandwidth provided by the cable service provider is lower than recommended,

you may encounter a blurry image or a temporary loss of video signal.

XXXXXXXXXXXXXXX

Monitoring

• < > : Takes a picture of current live image you are viewing.

• <

> : When enabled, you can hear what’s happening around the

camera.

` Depending on the policy of the Internet service provider, the sound output may not be

supported. (in either 3G UDP or Relay mode)

` Depending on your internet provider, When the camera can’t connect your phone or

PC directly, Relay mode show on display screen and the live video viewing may

time-out after 1 minute.

` The Night Vision video produces a different visibility according to the distance between

camera and subject. (See the picture below)

Alarm Settings

Camera has ability to send event notifications when motion or audio is detected.

See the notification bar below the live view.

1. From the bottom menu bar of the live screen, select to click one of SNS,

Messenger, and Email. The context menu should appear.

Provide the user ID and password that you have created and set in the previous site.

` If you fail to synchronize time, no event alarm will occur.

` In order to synchronize time, the device should be connected to the Internet.

1m distant (1.0 field) 2m distant (0.65 field) 3m distant (0.5 field)

· English

<YouTube> Notification

When enabled, you can record up to 30 seconds of video to your private YouTube

account.

1. Select Enable.

2. Enter your YouTube user ID and password.

3. Select public or private folder to save. By default, it’s set to private folder.

4. Click [Apply].

` You can check the recorded video at the YouTube homepage “Video Manager” 

“Uploaded”.

` Note that depending on the policies of YouTube, the video may not be uploaded.

` If setting to “public”, the video may be exposed to the public.

` It is advisable to create and use one YouTube account for each camera.

` Even when you have set the YouTube alarm, the video will not be transferred if the

event alarm is not set to Enabled (see page 23).

If a continuous motion is detected or the audio alarm occurs, the camera can

recognize the next event only after the uploading to YouTube is completed.

(In other words, it does not recognize any event until the YouTube upload is finished.)

<Picasa> Notification

When enabled, camera will send a picture of the event to your Picasa account.

1. Enter your Picasa user ID and password.

2. Select either public or private folder to save. By default, it’s set to private

folder.

3. Click [Apply].

If you have set the private setting of the video image, no image will be found in portal sites.

` Refer to the policy of Picasa for the maximum number of uploaded images.

` YouTube and Picasa must be enabled to receive notifications.

<My Friends> Notification

When enabled, camera will send event notifications to listed user IDs.

Notifications can be viewed in Smartcam App or Google Talk.

•

If this is set to <Enabled>, the video and image link recorded in YouTube and

Picasa will be transferred to the listed friends in real time in the event of an alarm.

• The video/image alarm will be transferred only if you have set the Youtube and

Picasa enabled. Otherwise, no alarm will be triggered.

• You will have no video displayed if you don’t have any Youtube ID and access a

private content.

•

Even when you access the Youtube site, no video will be played automatically.

Be sure to click the Play icon to play a video.

If you fail to play the video, log into the Youtube site and install Flash Player and try again.

• The Friend list will have user IDs registered at the Web site (www.

samsungsmartcam.com). When an alarm occurs, the PUSH alarm will be

notified to the respective smart phones via the Web site.

• If you want to receive the notification with Google Talk, follow the instructions

below to configure the Google Talk settings.

1. [email protected]

Monitoring

❖ <Google Talk> Notification

1) In the friend’s list, it shows the IDs that camera is registered to and Google

Talk friends that receives real-time notification from the camera.

2) When enabled, you can receive real-time event notification through Google

Talk messenger and Smartphone push service.

3) To receive instant event notification, add the camera as a friend to your

Google Talk messenger account. You have to add the following user ID.

(camera serial [email protected]) (i.e., XXXXXXXX@

xmpp.samsungsmartcam.com)

Once camera is invited, you will receive an instant message to enter the private

key for authentication. Enter the private key of the camera you are adding.

5) Once completed, you can see the Google Talk messenger ID in the camera

My Friends list.

6) Click [Apply].

<Twitter> Notification

When enabled, camera will send a notification as a message to your twitter account.

1. Click on “Request URL”.

2. Click on Get Token.

3. Twitter web page will pop-up for authorization.

4. Enter your Twitter user ID and password and click on “Authorize app” to get

the Access Token.

5. You will see the pin number generated. Copy the pin numbers and go back

to the camera page and paste the pin number in the Access Token section.

6. Click [Apply].

` The alarm notification will be sent to the specified user account via Twitter.

<E-mail> Notification

1. Please see the below table for the popular email server information.

Gmail Yahoo Yahoo Plus

Server Address smtp.gmail.com

smtp.mail.yahoo.

com

plus.smtp.mail.

yahoo.com

Port 465 25 465

Use SSL. Use Don’t Use Use

User

Authentication

on on on

ID Full email address

Only ID without

“@yahoo.com”

Only ID without

“@yahoo.com”

Password Email password Email password Email password

Sender Full email address Full email address Full email address

2. If your email provider is not listed, you need to get the email server

information from your email provider.

3. Add above information and receiver full email address and then click Add

button.

<Receiver email

address>

· English

Live Video Setup

Video Setting

No. Description

Event Alarm

Specify whether to trigger the alarm or not, and specify the sensitivity.

The higher the sensitivity is, the subtler motion/sound events will be

detected.

Flickerless

This will prevent possible screen distortion due to a mismatch between

the vertical sync frequency and the blinking frequency of the lighting.

Day/Night

Set the IR lighting.

If you set it to <Color>, the camera will not switch to the Day/Night

mode.

Audio

Adjust the volume of the built-in microphone and speaker of the

camera as appropriate.

Note that the Two-way audio transfer function is available only with the

smart phone application.

No. Description

Camera

You can configure the camera-related settings.

Flip: You can flip over the video image.

: Disable the screen rotation.

: Horizontally mirrors the video image against the vertical axis.

: Vertically flips over the video image against the horizontal axis.

: Rotate the screen by 180°

Brightness: You can adjust the brightness of the screen image.

Activation Time

You can activate the motion and audio detection at a desired time.

Always: It will work at all times.

Scheduled: You can select the time of activation.

` If you display more than one live video with the Web browser, they can be overlapped

in some portion. It is recommended to use one browser at one time.

` If camera is capturing a close object, the video analysis capability may degrade. In the

following cases, the video analysis function may not produce a proper result on the

default event and motion detections.

- The object color or brightness is similar to the background.

Multiple movements continue occurring at random due to a scene change or other reasons.

- A fixed object continues moving in the same position.

- An object hides other objects behind.

- Two or more objects overlap or one object divides in multiple portions.

- Too fast object (for a proper detection, one object should be found overlapping

between contiguous frames).

Reflection / blur / shadow due to a strong light such as direct sunlight, illumination, or headlamp.

- In severe snow, rain, wind or in dawn / dusk.

- A moving object comes close to the camera.

Monitoring

Network Setting

No. Description

Dynamic IP Address

If you select “Dynamic IP Address”, the IP address will be obtained

automatically.

Static IP Address

You must manually provide the information of: IP address, subnet

mask, gateway, DNS server address.

` If any of the manual settings is wrong, the network settings will not be applied.

` If you have both cable and wireless network connections simultaneously, the cable

network connection is prioritized.

` Press WPS to set the network connection to Wireless regardless of the current network

settings. When the system reboots, it will switch to Cable if the cable network

connection is already established.

` If you switch from the current wireless connection to the cable connection, the network

will switch to cable connection accordingly.

` For more information about the router or the wireless connection, refer to the

documentation of the router or contact the router manufacturer.

No. Description

Wireless On/

Wireless Off

You can select to activate or deactivate the wireless network

connection.

AP (Access Point) list

You will see a list of APs (Access Point) available. Select a desired one

from the list of APs (Access Point).

AP (Access Point)

password

If you select a secured AP (Access Point), you must enter the

password before you can access the network.

For the password, contact your network administrator.

` If you select a non-secured AP (Access Point), you just can access the network without

providing a specific password.

` If you entered a wrong password, you cannot access the network whatsoever.

` When the wireless network settings are completed, remove the LAN cable. If you do

not remove the LAN cable, the wireless network will not be available.

· English

Time Setting

No. Description

Time Zone Select your region.

Summer Time

Check this option if you live in a country or region where DST(Daylight

Saving Time) is applied.

` The time will synchronize with the NTP(Network Time Protocol) server automatically.

` For this, Internet connection is required.

` You need to set the timezone correctly to obtain the exact time setting.

` The time displayed without Internet connection may not be accurate.

No. Description

Change the private Key

You can change the private Key.

Enter the current private Key, and type a new private Key.

` If you change the private key, you will be logged out and return to the private key input

page.

` The private key can be changed only in admin mode.

` Keep the private key in a safe place as it is used for viewing the live screen of the

camera or for changing the display settings.

Admin

Private Key

Monitoring

No. Description

Update Firmware

Please update your current software version if it is lower than the

final version.

If the final version is the same as or lower than the current version, the

“Update Firmware” button will not be active. No update will proceed.

` Use the cable network if possible to update the firmware.

` If the power is off during the update, it will cause a fatal damage to the product.

` The duration of the firmware update depends on the size of the firmware file and the

network connection speed.

My Account

` If you want to change your information, move to “My account” page and select an

item (password and/or email address) and make changes as necessary.

XXXXXXXXXXXXXXX

Update Firmware

· English

Specifications 28

Product Appearance 30

Troubleshooting 31

appendix

Item Description

Video

Imaging Device 1/5" 3M CMOS

Effective Pixels 2,048(H) x 1,536(V)

Scanning System Progressive

Synchronization Internal

Frequency 120MHz(MAX)

Lens

Focal Length (Zoom Ratio) 2.87mm

Angular Field of View (D/V/H) 65.1°/ 42.9°/ 54.1°

Min. Object Distance 300mm ~ ∽

Focus Cotrol Fixed

Zoom Movement Speed Not Support

Lens Type 3 Plastic lens

Pan / Tilt / Rotate

Pan Range -15°~15° (Manual)

Tilt Range 0°~120° (Manual)

Specications

Specifications

Appendix

Item Description

Operational

On Screen Display (Web Browser,

Local page)

English, French, Germany, Spanish, Italian, Chinese, Korean

Camera Title Off / On (Displayed up to 15 characters)

Day & Night Auto(Infra-red Cut Removable), Color, B./W (850nm), 5m

OS Linux

Audio Detection Support

Motion Detection Video Motion Detection

Privacy Masking

Off / On

Privacy button

White Balance Auto

Digital Zoom Not Support

Flip / Mirror Yes

Network

Ethernet RJ-45 (10/100BASE-T)

Wireless Wi-Fi 802.11 b/g/n

WPS (Wi-Fi Protected Setup) Support WPS Button

Video Compression Format H.264, MJPEG

Resolution 640x480, 320x240

Max. Framerate 30fps (640x480)

Video Quality Adjustment

H.264: Compression Level

MJPEG : Quality Level Control

Streaming Capability Multiple Streaming (Up to 4 Profiles)

Item Description

Audio Compression Format G.711

Audio Communication 2-Way (Built-in Microphone, Speaker)

Protocol

TCP/IP, DHCP, SMTP, DNS, RTSP, RTCP, RTP, HTTP, TCP, UDP,

STUN, XMPP, SIP, uPNP, ICE, SNTP, IPv4/v6, ICMP

Streaming Method Unicast

Max. User Access 5 users at Unicast Mode

Web Viewer

Supported Browser :

Internet Explore (7,8), Safari, Firefox, Chrome (Silverlight prefered)

Mobile application support iPhone, Android (Not all android phones are compatible)

Environmental

Operating Temperature / Humidity 0°C ~ +40°C (+32°F ~ +104°F)/ 20% ~ 80% RH

Electrical

Input Voltage / Current 5V DC / 2.2A

Power Consumption Max. 7W

Indication 1 LED (Power, Status, Link)

CPU & Memory TI DM365 (216Mhz), SDRAM : 128MB, NAND : 128MB

Mechanical

Color / Material White/Plastic

Dimension (WxHxD) 54 x 90 x 30.07 mm (w/o Bracket )

Weight TBD

· English

Product Appearance

Appendix

If you encounter a problem with your system, see the table below to solve the problem

as quickly and easily as possible. Please follow the instruction below:

Troubleshooting

Problem Action

I forgot my user ID/

password.

- Move to “Log-in page  Find ID/PW”, and enter the registered e-mail

address to which we will send you the user ID and/or a new password.

It can be spammed out depending on the policy of the email server.

After logged in, it is advisable to change the temporary password provided.

I failed to connect

wirelessly with the

camera.

- If you encounter a frequent turn off of the wireless Internet LED, this may be

caused by an improper place for the wireless Internet network. Come closer

to the AP and try again.

- If the wireless network is unstable, you can still make connection via the

cable network.

After logged in, I

failed to register the

camera.

- Check if the entered serial number matches with the label on the bottom of

the camera.

- Please re-enter the valid private key and try again.

- If the problem persists, reset the camera to the factory default and start all

over again.

(To reset the camera to the factory default, press and hold the Privacy button

on the side of the camera. The camera will reboot when the factory reset is

completed.)

The camera is

registered, but is not

ready for network

connection.

- Check if the front LED on the camera turns on.

- If the wireless LAN LED turns off, follow the applicable instructions to make

the wireless LAN connection using WPS.

- If the problem persists even if the wireless LAN LED turns off, move the

camera near the wireless AP and try again.

- If you use the cable LAN network, the wireless LAN LED should turn off.

If the cable LAN is connected, the product will be connected to the server

automatically by the AP.

Problem Action

The camera video

is not uploaded to

YouTube.

- Move to Setup  Video Setting  Motion/Audio and adjust the sensitivity

as necessary.

- From the Notification settings page on the bottom of the live screen,

configure the YouTube notification settings. (See page 21 of the manual)

- YouTube has different service policies according to the country. The policy

for your country may prohibit uploading to YouTube. Please first check the

YouTube policy for your country.

- According to the YouTube policy, it may limit the uploading size. Check the

allowable free space of your YouTube account, and if insufficient, delete the

exiting video clips or increase the upper limit.

The capture images in

the camera will not be

uploaded to Picasa.

- Move to Setup  Video Setting  Motion/Audio and adjust the sensitivity

as necessary.

- From the Notification settings page on the bottom of the live screen,

configure the Picasa notification settings. (See page 21 of the manual)

- Picasa has different service policies according to the country. The policy for

your country may prohibit uploading to Picasa. Please first check the Picasa

policy for your country.

- According to the Picasa policy, it may limit the uploading size. Check the

allowable free space of your Picasa account, and if insufficient, delete the

exiting images or increase the upper limit.

Notification from

the camera is not

transferred to Twitter.

- Move to Setup  Video Setting  Motion/Audio and adjust the sensitivity

as necessary.

- From the Notification settings page on the bottom of the live screen,

configure the Twitter notification settings. (See page 22 of the manual)

The message of

Privacy mode appears

and no video is

displayed.

- The Company supports the privacy policy or mode for protecting your

privacy. The Privacy mode can be set using the button on the rear of the

product. (See page 6 of the manual)

- In Privacy mode, neither camera video will be displayed nor is it transferred

outside.

- To release the Privacy mode, press the same button again.

The video from the

camera is temporarily

lost.

- The video from the camera will be affected by the illumination of the

installation site of the camera. This is why the video from the camera looks

lost if the camera is installed in a low illumination environment.

- The video from the camera can be delayed according to a network delay.

Please check if the camera is installed in a place of proper wireless Internet

communications.

· English

Problem Action

No sound is output

from the video.

- Adjust the volume of the microphone or audio sound in the Setup page of

the camera.

- Click the Voice icon in the video playback page, or check if the voice is

turned On in your smart phone app.

- Depending on the policy of the Internet service provider, the sound output

may not be supported. (in either 3G UDP or Relay mode)

I forgot my Private

key.

- You must create a new private key.

- Press and hold the Privacy button in the rear of the product for at least 5

seconds to reset to the factory default.

- After the factory reset, access the camera and set the Private key again.

I want to change my

password and/or

email address.

- After logging in, move to the “My account” page, select an item (password

and/or email address) and make changes as necessary.

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate

collection systems)

This marking on the product, accessories or literature indicates that the product and

its electronic accessories (e.g. charger, headset, USB cable) should not be disposed

of with other household waste at the end of their working life. To prevent possible

harm to the environment or human health from uncontrolled waste disposal, please

separate these items from other types of waste and recycle them responsibly to

promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this

product, or their local government office, for details of where and how they can take

these items for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions

of the purchase contract. This product and its electronic accessories should not be

mixed with other commercial wastes for disposal.

Samsung Techwin cares for the environment at all product manufacturing stages, and

is taking measures to provide customers with more environmentally friendly products.

The Eco mark represents Samsung Techwin’s devotion to creating environmentally

friendly products, and indicates that the product satisfies the EU RoHS Directive.

SALES NETWORK

SAMSUNG TECHWIN CO., LTD.

Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400

TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745

SAMSUNG TECHWIN AMERICA Inc.

100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660

Toll Free : +1-877-213-1222 Direct : +1-201-325-6920

Fax : +1-201-373-0124

www.samsungsv.com

SAMSUNG TECHWIN EUROPE LTD.

Samsung House, 1000 Hillswood Drive, Hillswood Business Park Chertsey,

Surrey, UNITED KINGDOM KT16 OPS

TEL : +44-1932-45-5300 FAX : +44-1932-45-5325