User Manual
-V1.0-
Interactive Display
2
Safety Instruction
About This Document
A . Overview
Introduction
Parts
Ports
Remote Control
Temperature Control
B . Installation Guide
Safety Precautions
Installation Precautions
Installation
Installing the Internal PC (Optional)
Installing Newline Assistant
C . Getting Started
Power On
Power Off
Calibration
D . Operating the Interactive Display
Start Screen
Home
System Settings
Windows
Connection
Whiteborad
Add Shortcut
Gadget
File Management
End Meeting
E . Quick Setting Menu
F . Serial Port Control
G . FAQs & Troubleshooting
H . Specications
01
04
05
05
05
07
09
11
12
12
13
14
15
16
17
17
18
19
22
22
22
27
39
40
40
49
52
53
56
59
60
65
68
71
Contents
More InformationI .
Thank you for choosing the TRUTOUCH VN series interactive display. Please use
this document to get the most out of your display.
Welcome to the world of TRUTOUCH.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:(1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
NOTE 1:This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
●
Reorient or relocate the receiving antenna.
●
Increase the separation between the equipment and receiver.
●
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
●
Consult the dealer or an experienced radio/TV technician for help.
The symbol of the crossed out wheeled bin indicates this product
should not be placed in municipal waste. Instead, dispose of waste
equipment by taking it to a designated collection point for electrical
and electronic equipment recycling.
NOTE 2: Any changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
1
Safety Instruction
For your safety, please read the following instruction before you use the product. Serious injury
or property damage may be caused by improper operations. Do not try to repair the product on
your own.
Disconnect the product from power supply immediately if major failures
occur.
Major failures include the following:
●
Smoke, peculiar smell or abnormal sound is discharged from the product.
●
No image or sound is displayed, or the image error occurs.
In the preceding scenarios, do not continue to use the product. Disconnect
power supply immediately and contact professional staff for troubleshooting.
Do not drop liquid, metal or anything combustible into the product.
●
If any liquid or metal is dropped into the product, power off the product and
disconnect power supply, then contact professional staff for solutions.
●
Pay attention to children when they are close to the product.
Put the product on a stable surface.
An unstable surface includes and is not limited to an inclined plane, a shaky
stand, desk or platform, which might cause turnover and damage.
Do not open the cover or change the product on your own.
High voltage components are installed in the product. When you open the cover,
high voltage, electric shock, or other dangerous situations may occur.
If inspection, adjustment, or maintenance is required, contact the local distributor
for help.
Use the specied power supply.
●
To prevent the product from being damaged, do not use any cables other than the
one provided with the product.
●
Use a three-wire socket and ensure that it is properly grounded.
●
Pull out the power plug from the socket if the product is not used for a long period.
Clean the dust and metal on the power plug regularly.
●
Fire or electric shock may be caused if the product is powered on, when you
are cleaning.
●
Pull out the power plug before cleaning it with a dried cloth.
The voltage/current of the rear power output port is 5 V/2 A (maximum). Purchase
the power code/AC adapter according to customer needs. The port can be used
for Newline Android box X10D. Please do not connect any products with different
power requirement. Otherwise, it may cause damage to products or re.
WARNING
2
Do not put items on the top of the product.
●
Do not put items, such as a container for liquid (a vase, owerpot, cosmetics
or liquid medicine) on the top of the product.
●
If any water or liquid is spilled on the product, a short circuit may occur and
cause re or electric shock.
●
Do not walk on or hang any items on the product.
Do not install the product in an improper place.
●
Do not install the product in humid places, such as the bathroom, the shower
room, near windows, or outdoor environments that experience rain, snow or
other harsh weather. Avoid installation near hot spring vapor. The preceding
environments may cause faults in the product or electric shock under extreme
conditions.
●
Do not put exposed re source, such as an ignited candle, on the product.
Pull out the power plug during thunderstorms.
●
Do not touch the product during a lighting storm to avoid electric shock.
●
Install or place components that supply high enough voltage to cause personal
injury out of the reach of children.
Do not touch the power cable with wet hands.
Do not install the product in high temperature environments.
●
Do not install the product near a heat source, such as a radiator, a heat
reservoir, a stove or other heating products.
●
Do not expose the product to direct sunlight, which may cause high
temperatures and subsequent faults in the product.
For transport.
●
Pack the product for transport or maintenance by using the cartons and
cushioning material provided with the product.
●
Vertically move the product during transport. The display or other components
are easily broken if the product is moved by an improper way.
●
Before you move the product, disconnect all external connections and separate
all toppling preventing products. Move the product carefully to prevent it from
being hit or squeezed, especially the screen, which may cause injury if broken.
Do not cover or block up any vents on the product.
●
Any overheated components may cause re, damage the product, and shorten
the service life.
●
Do not lay the product down where the venting surface will be covered.
WARNING
CAUTION
3
●
Do not install the product on a carpet or cloth.
●
Do not use a cloth such as table cloth to cover the product.
Use the battery correctly.
●
Galvanic corrosion, electric leakage, and even re may be caused by improper
battery usage.
●
It is recommended to use the designated type of battery and install the battery by
correct electrodes (positive and negative).
●
Do not install and use a new battery with a used one.
●
Take out the batteries if the remote control is not used for a long period.
●
Do not expose the
batteries
to overheated environments such as sunlight and ring.
●
Dispose of the used batteries based on your local regulations.
Do not damage the power cable.
●
Do not damage, change, twist, bend, or forcibly drag the power cable.
●
Do not put weights (such as the product itself) on the power cable.
●
Do not forcibly drag the cable when you pull out the power plug. If the power
cable is damaged, please contact the local distributor to repair or replace it.
●
The power cable in the accessory box is for this product only. Do not use it on
other products.
Additional advice:
●
U
se the product in an environment with comfortable lighting. It is harmful to your
eyes
to watch in a too bright or too dark environment.
●
Relax your eyes after a period of time for watching.
●
Keep sufcient distance from the product to protect your eyes and prevent
eyestrain.
●
Adjust the volume to an appropriate level, especially at night.
●
Use amplier equipment as the audio input source with caution. If you must use amplier
equipment, the input power should not exceed the maximum of speaker power.
Otherwise, the speaker can become overpowered and damaged.
About USB port.
Front USB 2.0 ports and rear USB 3.0/USB 2.0 ports switch connections based
on signal sources. If the current signal source is reading the data from an
external product connecting to the port, please switch the signal source after the
data reading is complete. Otherwise, the data or product may be damaged.
Keep away from the product when you use a radio.
The product complies with the international EMI standard to pervent radio
interference. However, interference may still exists and causes noise in the radio.
If noise occurs in the radio, try the following solutions.
●
Adjust the direction of the radio antenna to avoid the interference from the product.
●
Keep the radio away from the product.
CAUTION
4
About This Document
This document describes multiple functions, instructions, and notes about the product.
Symbols are used in this document to indicate operations that need particular attention. The
symbols are dened as follows:
Provides additional information to supplement operation in the main
text.
Provides tips for operation.
Indicates a potentially hazardous situation that, if not avoided, could
result in equipment damage, data loss, performance deterioration, or
unanticipated results.
Indicates a hazard with risk that, if not avoided, could result in death or
injury.
WARNING
CAUTION
NOTE
TIP
5
A
Overview
Introduction
The Interactive Touch display adopts the advanced touch technology and All in One
design, and integrates video, audio, touch, writing, and multi-media presentation
functions. This product does not require additional products, installation and wiring, and
commissioning and maintenance to function.
Dedicated smart system is customized as a meeting assistant. It can meet requirements
of various meeting modes, implementing convenient comments on local documents,
viewing multi-media files, conducting multi-party remote video and audio meetings,
managing local les, and improving the meeting experience and work efciency.
●
●
●
All-in-one design facilitates operation and saves complex hardware and software setting.
4K HD LED screen uses full lamination technology and high gamut backlight, which
completely avoids light refraction and ghosting problems and enables a clear, light
and thin screen.
Provide perfect writing experience, enable writing mode to be switched over in the
Windows and smart systems, and automatically identify pen thickness and color. With
a feel like writing on paper, meeting quality is signicantly improved.
Parts
Front View
1
2 34
5
6
6
Rear View
● TT-8618VN/TT-7518VN
9
7
8
10
1 2
3
4
5
6
7 8
9
10
Speakers
Front Ports
Button Cover
Front Buttons
Pen/Eraser Tray Cover
Pen/Eraser Tray
Power Supply Plug
Rear Ports
Internal PC Port (OPS)
Power Switch
● TT-6518VN
7 8
10
9
7
Front Ports
Rear Ports
Ports
Front USB 2.0 ports and rear USB 3.0/USB 2.0 ports switch connections based on signal
sources. If the current signal source is reading the data from an external product connecting to
the port, please switch the signal source after the data reading is complete. Otherwise, the data
or product may be damaged.
CAUTION
The voltage/current of the rear power output port is 5V/2A (maximum). Purchase the power
code/AC adapter according to customer needs. The port can be used for Newline Android box
X10D. Please do not connect any products with different power requirement. Otherwise it may
cause the damage to products or re.
WARNING
8
You are advised to connect X10D to HDMI rear 2.
Tip:
Embedded
USB2.0
● TT-8618VN/TT-7518VN ● TT-6518VN
9
Front Buttons
Buttons Operations Functions
Power Short press
Power on/off
Indicator LED status:
●
Steady on red: shut down mode
●
Steady on green: working state
Home Short press Go to the home page
Return Short press Return to the last menu/Exit
Menu Short press Open the menu
Vol-
Short press Decrease the sound volume
Long press for more than 1 second
Decrease the
sound volume continuously
Vol+
Short press Increase the sound volume
Long press for more than 1 second
Increase the sound volume
continuously
Remote Control
Carefully read the following instructions before using the remote control to avoid possible faults:
●
Do not drop or damage the remote control.
●
Do not spill water or other liquids on the remote control.
●
Do not place the remote control on a wet object.
●
Do not place the remote control directly under sunlight or near an overheating heat source.
CAUTION
10
Buttons Functions
Power On/Off.
Switch Source to Internal
PC.
Mute/Unmute Audio.
Freeze the Current Screen,
Click Again to Exit Freeze
Function
.
Conrm/OK.
Up/Down/Left/Right.
Return to Previous/Exit.
●
Short Press: Go to the
Home Page.
●
Long Press: View Currently
Running Applications.
Take a Screenshot.
Decrease the Sound Volume.
Increase the Sound Volume.
Open the System Settings.
Page Up.
Page Down.
Zoom In.
Zoom Out.
Switch Source to HDMI
Front.
Switch Source to HDMI
Rear 1.
Switch Source to HDMI
Rear 2.
Buttons Functions
Switch Source to HDMI
Rear 3.
Toggle Display Backlight Mode
(including Auto,
Standard and
EnergyStar mode).
Switch Source to DisplayPort
.
Open the Display Menu or
External Source Menu.
11
Temperature Control
In certain special installation or operation environments, the ventilation condition
of the screen is poor and the heat dissipation efficiency is low. As a result, the
internal temperature can rise. When the internal temperature sensor detects that the
temperature has reached the threshold, the system will go to shut down mode to avoid
any permanent damages to the components caused by high temperature. Please check
the device and environment, and turn the power on again.
12
B
Installation Guide
Installation Environment
Installation Direction
Safety Precautions
Keep Away From
Combustible Vapors
(gas leaks, etc.)
Do Not Use
Outdoors
Keep Temperature
Below 120 F
( ≤50 c)
Hang the Product Horizontally No Vertical Installation Do Not Lay Flat
13
Weight Loading
Installation Precautions
Weight of the product: 87.1 lb/39.5 kg (TT-6518VN), 111.3 lb/50.5 kg (TT-7518VN),
143.3 lb/65 kg (TT-8618VN)
When using a mobile stand, please ensure the weight of the product is less than the
loading capacity of the mobile stand.
Do not install the product where it might be hit by a door.
When using the wall-mount bracket, please ensure the wall can support the weight of
the product. We recommend that the wall surface be reinforced and have a loading
capacity 4 times of the weight of the product. Please consult a professional installer
for wall-mount installation.
●
●
●
Ventilation
Ensure adequate ventilation and/or air conditioning environment. We recommend
keeping certain distances from the side of the product to the wall or panels. Ventilation
requirement is shown in following gure.
Top ≥ 200 mm
(7.78 in)
Left ≥ 100 mm
(3.94 in)
Right ≥ 100 mm
(3.94 in)
Back ≥ 100 mm
(3.94 in)
Bottom ≥ 200 mm
(7.78 in)
The company does not undertake relevant legal responsibility for any problem caused
by improper operation, if the third party mobile stand, or wall-mount bracket is beyond the
scope of the product.
Note
14
The dimensions of the 4 bracket mounting holes on the back panel are VESA MIS-
Fcompliant (TT-8618VN or TT-7518VN: 800 x 400 mm/31.50 x 15.75 in; TT-6518VN:
600 x 400 mm/23.62 x 15.75 in). Please use metric M8 screws with length of 10
to 15 mm (0.40 to 0.59 in) to secure the touch display with the mounting system.
Dimensions of the mounting holes on the back panel are shown in the following
gure.
Installation
● TT-8618VN/TT-7518VN
● TT-6518VN
M8
800 mm (31.5 in)
400 mm (15.75 in)
M8
M8
M8
600 mm (23.62 in)
400 mm (15.75 in)
M8
M8
M8
M8
Consult a professional installer to install the display product.
Note
15
Installing the Internal PC (Optional)
The internal PC does not support hot plugging. Therefore, you must insert or remove it when the
display is powered off. Otherwise, the display or internal PC may be damaged.
The internal PC is not congured by default. You need to purchase the internal PC separately.
Perform the following steps to install the internal PC.
You will need to purchase the internal PC separately. Perform the following steps to install the
internal PC.
CAUTION
Step 1
: Unscrew the M3 screws by
hand to remove the internal PC
shielding cover.
Step 2
: Push the internal PC into the
internal PC port at the rear of
the display from right to left.
Step 3
: Secure the internal PC to the
display by using the M3 screws.
Step 4
:
Ensure the installation is
correct before turning the
power on again.
M3
M3
16
Installing Newline Assistant
Newline Assistant is the tool used as a bridge between smart system and Internal PC (OPS). It
helps to add windows software to smart system as well as to protect USB data/camera when
switching between sources.
Therefore we strongly recommend users install Newline Assistant after installing the internal PC.
Step 1
: Install Internal PC correctly.
Step 2
: On the
Home
page, click
Windows
. It will switch the signal source to Internal Windows
system.
Step 3
: Log in to the website www.newline-interactive.com and choose
Products > Software
to
download the Newline Assistant installation package.
Step 4
: Install Newline Assistant as instructed.
Introduction
Installation
17
17
Step 1
: Plug the power supply into the power outlet fully and plug the power connector
into the side of the product. Ensure the power is in the range of 100 V to 240 V
with frequency at 50 Hz/60 Hz ± 5%. The power current must be grounded.
Power On
C
Getting Started
The power outlet should be installed near the equipment and shall be easily accessible.
Note
Step 3
: Press the power button
on the front control panel or on the remote control.
Step 2
: Flip on the power switch located on the side of the product to “On”.
Power Switch
Power Supply Plug
Power Switch
Power Supply Plug
● TT-8618VN/TT-7518VN
● TT-6518VN
18
Power Off
Step 1
: Power off the screen in the following situations:
If there is whiteboard data or screenshot(s), store your meeting documentations
before powering off the touch screen. Otherwise, the product will delete your
meeting documentations after the meeting is complete.
●
Step 2
: Press the power button on the front panel or the power button on the
remote control again. The
Warning
dialog box will be displayed as shown in
the following gure.
front panel or the power button on the remote control to power off the screen.Go
to Step 4.
If there is no whiteboard data or screenshot(s), press the power button on the
●
Press the power button on the front panel or the power button on the remote
control.
The
Save meeting discussion
page will be displayed as shown in the
following gure.
19
Step 4
: If you are not going to use the product for an extended period of time, we
recommend you to switch the power switch to “Off”.
Step 3
: In the
Warning
dialog box, click
Cancel
. You can save les if desired. After
les are saved, return to Step 2. Click
Conrm
, and the power indicator will
turn to red.
If the cursor position has a big deviation from the actual touch point, calibration is used to
eliminate the deviation. Positioning is required in the following scenarios:
●
The internal PC is used.
●
A computer is connected through the HDMI or DisplayPort interface.
If the positioning is not correct, perform the following operations to calibrate again. The
following takes Windows 10 as an example:
Step 1
:
Ensure that the HDMI or DP interface and external products are connected
properly.
Step 2
: Select the corresponding Windows signal from the signal source menu. The
Windows page will be displayed.
Step 3
: Select
Tablet PC Settings
on the
Control Panel
page.
●
If an internal PC is equipped, the internal PC and the screen are powered off
simultaneously when you power off the system.
●
Do not forcibly disconnect the power supply of the screen when the internal PC is on.
Note
Interface operation on the Smart system does not need positioning. External products
with Microsoft Windows 7 or later versions will require positioning.
Note
Calibration
20
Step 5
: Select
Touch input
from the option and start calibration.
Step 4
: Select in the Tablet PC Settings window.
21
Step 6
: Use nger or pencil to click and hold the center of the ickering cross . Do not
release it until moves to the next positioning point. Complete the calibration
process as instructed.
Step 7
: After the calibration is complete, the
Digitizer Calibration Tool
dialog box will be
displayed. Click
Yes
to save calibration data.
To provide calibration samples, tap the crosshair each time that it
appears on the screem.
Right-click anywhere on the screen to return to the last calibration
point. Press the Esc button to close the tool. Do not change your
screen orientation until you have completed the calibration process.
Step 8
:
The
Tablet PC Settings
dialog box will be displayed again. Click
OK
. The positioning
will be complete.
●
To ensure writing accuracy, use the pencil or stylus included with the product for proper positioning.
●
Positioning errors may cause failure of touch functions of the display. In that case, please perform
positioning again.
Tip:
22
D
Operating the Interactive Display
Start Screen
Home
When the product is turned on, the product will show the start screen page. As shown
in the following gure.
Touch the screen to start a meeting, and the product will go to the
Home
page. As
shown in the following gure.
1
2
4 4
5
6
3
1
Logo (Shortcut to Settings)
5
Status Bar and Settings
2
Clock (Shortcut to World Clock)
6
Main Toolbar
3
Date and Week (Shortcut to Calendar)
4
Side Toolbar
23
Shortcut for Settings
Shortcut for World Clock
Click the icon on the
Home
page to enter the
logo & Wallpaper Setting
page
to set the logo and wallpaper. The logo and wallpaper can be obtained locally or from a
device connected via the USB port, as shown in the following gure.
Click the time icon on the
Home
page to enter the
Time Converter
page and convert
the time and zone. Click to add other time zones indicating other countries, as
shown in the following gure.
24
Shortcut for Calendar
Click this icon to enter the
Calendar
page and set schedules and synchronize with Google
calendar, as shown in the following gure.
Shrink1:
Shrink2:
Expand1:
Expand2:
Side Toolbar
The Annotation Mode/Discussion Mode/Home/Return/Windows icons are displayed
by default in the toolbar at two sides of the screen. The bottom side toolbar can be
customized as your choice (The default icon is Windows). You may also hide the side
tool bar at the setting or move it up and down, shrink or expand by gestures. You may
double-click the to expand or shrink the toolbar. Long press the customized icon to
unfold level-2 icons.
25
Icon Functions
Enter annotation mode, and click again to stop annotation and save
screenshot.
Enter discussion mode.
Go to Home page.
Return to the last menu/Exit.
Enter the internal PC source.
Manage currently running applications.
Slide left/right the currently running application or click × at the upper right
corner to close the application.
View all gadgets.
Enter the favorite source.
The functions of the side toolbar are as follows:
Status Bar and Settings
Icon Functions
If USB ash memory(s) is connected to the USB port, this icon will be turned
on. For details on the wiring method of the USB port, see section "Ports".
If the product is connected to Ethernet, the icon will be turned on. For details
on the wiring method of the wired network, see section "Ports".
If the product is connected to a wireless network, the icon will be turned
on. For details on the wiring method of the wireless network, see section
"Ports".
Access the system setting page.
The upper right corner of the home page displays three working status icons (including
USB ash memory(s), Ethernet, and Wi-Fi), and system setting shortcut.
26
Icon Functions
Switch to the internal PC source.
Enter
Connection
to switch to the connected product, including cabled
signal sources and wireless applications.
●
Cabled signal sources include HDMI Front, HDMI Rear (1 to 3), and DisplayPort.
●
Wireless applications include Montage and Trucast.
Discussion
provides discussion board function and screen annotation
functions.
Gadget displays all pre-installed applications, including
Ofce viewer
,
Email
,
Calendar
,
Gallery
,
World clock
, and
Calculator
. Click the icon of an
wwapplication to run the application.
Open the File Manager, and you can can explore on internal and external
les of the screen.
Click
Add
to enter
Add
page, you can add up to 7 shortcuts to your favorite
software, gadgets or connections to the Home page. (See more detail in “Add
Shortcuts to Home Page”)
Click
End
to end a meeting. Users will have the choice of saving the
discussion boards screen captures and ending the meeting. Once a meeting
is ended, all screenshots and discussion data are cleared.
Main Toolbars
27
Network Settings
Enter the
Network
submenu to set a LAN, enable Wi-Fi, view network information, and
enable the Wake up via LAN function.
●
LAN setting: Automatically obtain the LAN IP address or set static IP address
according to requirements.
●
Wi-Fi: Click corresponding button to enable the Wi-Fi function.
●
Status: View IP address, MAC address and work time of the display.
●
Wake up via LAN: Click corresponding button to enable the Wake up via LAN
function. Connect the display and PC to a same LAN using cables, run the Wake up
via LAN, and search for the IP address and MAC address that match the display.
Enter the system setting page using one of the following methods:
●
Click or on the
Home
page.
●
Press on the remote control.
●
In the
Quick Setting Menu
, click the icon.
System Settings
28
Language and Input Method Settings
The default input method of the system is
FloatNSplit Table Keyboard Plus
, and
Hardware
keyboard
must be enabled. If you want to switch to another language,
switch the keyboard input method via
Keyboard & input methods
, in addition to
switching the language.
FloatNSplit Table Keyboard Plus does not support Chinese and Japanese.
Note
Enter the
Language & Input Method
submenu to set language and input method.
29
FloatNSplit Table Keyboard Plus description:
●
:
Drag this icon and change the size of the keyboard.
●
: Drag this icon to move the keyboard.
●
: Click this icon to switch the keyboard unfold mode.
Setting a Language
Click
Language
at the right side. In the
Change language
dialog box that is displayed,
select a language.
30
Adding an Input Method
Click
Current keyboard
at the right side. In the
Change keyboard
page, click
CHOOSE
KEYBOARDS
, unfold
Keyboard & input methods
, and click the button at
the right side
according to reference to add an input method (multiple choices can be selected).
Setting an Input Method
Select an input method at the right side to set the attributes of the input method.
31
Enter the
Apps
submenu to view downloaded applications by type, running applications,
and all applications.
APPs
Enter the
Storage
submenu to view space distribution of the internal storage.
Storage
32
Date and Time Settings
Setting a Date
You can automatically obtain the system date or customize a date.
●
To automatically obtain a date, select
Automatic date & time
.
Enter the
Date & Time Setting
submenu to set the date and time. Before setting the date
and time, users should click
Select time zone
to select local time zone.
●
To customize a date and date format, set them in
Set date
and
Choose date format
.
33
Setting Time
You can automatically obtain the system time or customize time.
●
To automatically obtain time, select
Automatic date & time
.
●
To customize time and time format, set them in
Set time
and
Use 24-hour format
.
34
Enter the
Power ON/OFF Setting
submenu to set automatic power on/off time and the
time
for
the system to enter the shut down mode.
●
To set the automatic power on time, select
Auto power on
, and set the power on time
in
Power on time
, as shown in the following gure.
●
To set the automatic power off time, select
Auto power off
, and set the power off time
in
Power off time
, as shown in the following gure.
Power ON/OFF Setting
35
●
To set the energy saving time, click
Energy saving
. In the dialog box that is displayed,
set a duration after which the display enters the lock mode if the display is left un-
operated. After the display is locked, if the user does not operate the display within
120s, the display enters the shut down mode. The duration can be set to
30 MIN, 60 MIN,
90 MIN
, or
NEVER
. You can also customize this duration and the range is 3 minutes to
480
minutes.
NEVER
indicates that the automatic shut down mode function is not enabled.
Note
36
Tool Bar Setting
Enter the
Tool Bar
submenu to set whether to display the side tool bar and icons.
●
Left: Click to turn on/off the left tool bar.
●
Right: Click to turn on/off the right tool bar.
●
Customized icon: Click the icon under
Customized icon
to display the last shortcut
key at both sides of the tool bars. If you dene the shortcut key as
Connection
, you
can set a signal source to enter after this shortcut key is clicked in
Favorite Connection.
Input/Output Setting
Enter the
Input/Output Setting
submenu to set the automatic power on/off function of
the consumer electronics control (CEC) device, new signal source, and resolution of
image output through the HDMI port.
●
After the
CEC auto power on
function is enabled and the display is connected with
the CEC device via the HDMI port, the display automatically starts if the CEC device
starts and the display receives a CEC startup command.
●
After the
CEC auto power off
function is enabled and the display is connected with
the CEC device via the HDMI port, the CEC device automatically stops if the display
stops and the CEC device receives a CEC shutdown command.
●
After the
New input source
function is enabled, the system can automatically switch
to the screen of the newly connected signal source.
37
Logo and Wallpaper Setting
Enter the
Logo & Wallpaper Setting
submenu to set background, lock page, or Home
page log.
On this page, click
View
to select a picture and automatically upload it to replace
current picture. Click
Default
. The logo and wallpaper are reset to Newline pictures.
Smart Eye Protection
Enter the
Smart Eye Protection
submenu, according to the need to open the eye. The
eye protection feature includes the image display effect, the display brightness of the
white board at the time of writing, automatically changing the display brightness of the
screen and ltering the blue light function according to the ambient brightness. The lter
level can only be set if the Bluelight lter is enabled.
38
Newline Extension
Enter the
Newline Extension
submenu to set external devices (Trucast, X10D, and
Trucam) to be displayed in the
Cable Connection
column of
Connection
and the
wireless application Montage to be displayed in the
Wireless Connection
column.
Furthermore, you can set the HDMI Rear channel to be displayed on the Trucast,
X10D, or Trucam screen. If an auxiliary device of our company X10D is connected, the
system identies it through the CEC signal and automatically enables and switches to
corresponding channel.
39
About
Enter the
About
submenu to view firmware or system version information, system
upgrade, and factory setting.
On the
Home
page, click
Windows
to enter the Internal PC source page, as shown
in the following gure. If the screen is not equipped with an internal PC, "No Signal" is
displayed.
Windows
40
On the Home page, click
Connection
to enter the connected product, including cabled
signal sources and wireless applications.
●
Cabled signal sources include HDMI Front, HDMI Rear (1 to 3), and DisplayPort.
You can preview the image of the corresponding signal channel. If the channel has no
signal input,
No Signal
will appear. You can click the selected signal source to switch
to the corresponding channel in full screen. You can also long press the signal source
page and enter remark information in the
Modify remarks
dialog box that is displayed.
If
Trucast, Trucam, or X10D options have been enabled in
Newline Extension
,
corresponding channel cannot be remarked.
●
Wireless applications include Montage and Trucast.
Connection
Montage should be installed manually to the internal PC rst. If the Montage software is not
added to the Newline assistant, the system prompts users to install Montage and add it into the
Newline assistant. For details on the addition method, see section “Add Shortcuts to Home Page".
Note
The rst time you turn the display on, only the cable connections appear in
Connection
.
Wireless connection can be added in the
Newline Extension
setting. In this case, the
name and icon of the HDMI on the left cabled channel change as the Trucast application
is enabled or an external product is connected. For details on the configuration, see
section “Newline Extension”. After the setting is successful, connect the Trucast, X10D
and Trucam to corresponding HDMI ports of the display.
The whiteboard has the following functions:
●
Discussion and screen annotation
On the whiteboard page, you can select pen type, width, and color to write or annotate
Whiteborad
41
●
Click
Discussion
in the main toolbar or click in the side toolbar to enter the
discussion mode, as shown in the following gure.
1 2 3 4 5 6 7 8 9
10
11
●
Click in the side toolbar or click in the discussion mode to enter the annotation.
In annotation mode it would generate a transparent layer above the screen, and user
could add the annotation on it until they exit the annotation mode.
Whiteboard Mode
on the screen. You can also erase selected content or clear all contents.
●
Page navigation
Preview or delete pages.
12 13
14
42
SN Icon Name Icon Function
1 Mode Switch
Click the icon to switch between annotation mode and the discussion
mode. (See more detail in whiteboard mode section)
2 Pen
Click to use the pen function, and the icon turns into blue. Click and hold
the icon for two seconds to set the size or color.
3 Highlighter
Click to use the highlighter function, and the icon turns into blue. Click
and hold the icon for two seconds to set the size or color.
4 Eraser
Click to select the eraser function, when it is selected, the icon turns into
blue. Click and hold the icon for two seconds to set the size of eraser.
5 Clear Clear all data in this page.
6 Undo Back to the previous step.
7 New Page
Click to add a new page. Click and hold for two seconds to set the color
and the pattern of the new page.
8 Previous Page Click to back to the previous page.
9 Next Page Click to go to the next page.
10 Navigation Click to show the page thumbnails.
11 Page Number Shows which page is used right now.
12 Hide Smart Bar Click to hide or show the smart bar.
13 Cursor
Click to use the cursor to control the Internal PC or external device.
When the function be selected, the annotation part is still on the screen.
14 Screenshot
Click to print screen, and save the data in le management.
Click and hold the icon for two seconds to show the pop-up windows to
make users to choose if they want to save the screenshot automatically
when they leave the annotation mode.
Whiteboard Functions
New Page and Settings
In discussion mode, click to create a new page. Up to 20 pages can be created.
See the following gure.
●
Create a new page
43
●
Page settings
Click and hold for two seconds to set the color and the pattern of the new page,
as show in the gure below.
Switch Whiteboard Mode
Click and in the lower left corner of the discussion mode to switch between
whiteboard modes.
●
: Annotation mode
The background is transparent and the real-time image of the current signal source will
be displayed. You can comment on presentation content such as Ofce documents and
pictures as showing in the following gure.
44
●
: Discussion mode
The background is in mono color, as shown in the following gure. You can write content
on the page as required.
On the Whiteboard, two types of pens are supported: Pen and highlighter.
●
Pen : used to write.
●
Highlighter : used to highlight. Characters covered by comments are visible.
Pen Type
Line Size and Color
On the Whiteboard, click and hold or for two seconds to set the size and color.
You can select the line size and color for writing, as shown in the following gure.
45
Two methods are available to erase written errors or content as follows:
●
Five-nger gesture: touch the screen with ve ngers at the same time. A circle shows
and indicates the area for eraser. Move the circle with ngers to erase written contents.
●
Fist/hand back erasing: corresponding erase shape is a round with diameter 100pt.
●
Spot erasing: Click to clear wrong or unnecessary content. Click and hold the icon
for two seconds to set the size of eraser (S 10pt/M 30pt/L 50pt), it would be shown
by the icon, as shown in the following gure.
Eraser
Screenshot
In annotation mode, click to save the current image as a picture. Up to 50 screenshots
screenshots can be created. Click and hold the icon for two seconds to show the pop-
up windows to make users to choose if they want to save the screenshot automatically
when they leave the annotation mode, as shown in following gure.
46
Pictures saved through screenshots can be viewed and obtained using the following
methods:
●
After a meeting is complete, screenshots are saved on the
Save meeting Discussion
page, as shown in the following gure.
●
Click on the home page and choose
Internal storage > Pictures > Screenshots
> image
to view or obtain screenshots.
47
On the Whiteboard page, click to show the pop-up windows to make users to choose
if they want to clear contents on current page, as shown in the following gure.
You can preview, select, and delete a created writing page.
Clear All
Page Operations
Click at the lower right corner in the discussion mode. All pages will be displayed.
Click one page to switch to that page for more operations, as shown in the following
gure.
Page Preview
48
On the
Navigation
page, you can select or delete writing pages according to
requirements, as shown in the following gure.
Page Selection and Deletion
●
Click to select all pages.
●
Click to delete selected pages.
Only 8 pages are displayed at once, and you can slide right or left by one nger
to see more.
Note
49
Add Shortcut
Add Shortcuts to Home Page
Step 2
:
Click the icons on top to switch the list between Windows programs, external
signal sources, and pre-installed gadgets.
Step 1
:
On
Home
page, click the
icon in the lower right corner. The interface for adding
shortcuts will be displayed.
Click to view the Windows programs that the Newline Assistant uploads to
the
Smart system. For details,see "Add Quick Start Windows Programs in
Smart System".
●
Click to view signal sources in
Connection
. You can set the Newline
accessories to signal sources at Newline Extensions setting.
●
Click to view Gadget applications.
●
50
In the list, click the icon to add it to the shortcut on the
Home
page. The check
icon will appear at the bottom of the shortcut icons. Up to 7 shortcuts can be
added.
Tap the icon with the check mark again, the check icon will disappear and the
shortcut will be deleted from the
Home
page.
Step 4
: At the
Home
page, click the shortcut icon and you can start the program/
application or change to the external signal source.
●
●
Step 3
: Add or delete applications on the tab.
Add Quick Start Windows Programs in Smart System
Step 1
: In Windows, run the
Newline Assistant
program and drag the software icons
or folder shortcut icons that you want to add from desktop or menu to the
Newline Assistant
window. The applications added or deleted through the
Windows system will be automatically updated to the smart system until the
upload progress reaches 100%. If there is an application not updated, click
in the upper right corner to manually update all icons in the Newline assistant
window to the smart system.
Only .exe le and folder are supported.
Tip:
51
Step 2
: Click to return to the
Home
page. Click the icon and go to shortcut setting.
The page for adding application program will be displayed.
Step 3
: At the shortcut setting page, click icon to view all the Windows programs
added by Newline Assistant in Step 1.
By default, the Newline Assistant application is added on the tab.
Note
Step 4
: Tap the icon and add the shortcut at the Home page. Tap again and remove it.
Step 5
: Return to
Home
page. Click the icon of an added Windows software to start the
software.
52
Gadget
On the
Home
page, click
Gadget
. On the page that is displayed, all applications can be
viewed. The following gure shows applications that the system is delivered with.
Icon Functions
Click this icon to enter the Calendar application, set schedule, and update to
Google Calendar.
Click this icon to enter the system setting page.
Click this icon to enter the calculator application.
Click this icon to enter the email application and send les. Before sending
les, you need to create an email account.
Click this icon to enter the Ofce viewer application. In this application, you
can view ofce les, including excel, word, power point, and PDF les.
Click this icon to enter the World clock application. In this application, you
can convert time and zone.
53
File Management
The product supports connection to USB flash memory. Enter the File Viewer
application, you can preview all files in the internal storage and storage devices
connected via USB ports and select, copy, paste, delete and search for les.
On the
Home
page, click
File Viewer
, as shown in the following gure.
File Viewer Page
Enter the
File Viewer
application, you can click the submenu at the left side according
to requirements, preview internal storage, external storage devices connected via the
USB ports, cloud stored les, FTP uploaded les, and local network les, as shown in
the following gure.
File Preview
54
You can click the menu at the left side to display les by types, for example, document,
picture, music, video, archive and downloaded. You can also click to lter les by
picture, music and video.
●
The system supports two view modes: list and thumbnail. You can click and at
the top right corner to switch view modes, as shown in the following gure.
●
Click to display les based on name, type, size, and modication time in an
increment or decrement manner.
File Filtering
55
File Search
Enter the
File Viewer
application, and click . In the dialog box that is displayed, enter
keywords in the search box according to requirements. The system will display a list of
les that match the keywords.
Enter the
File Viewer
application. You can create folders according to requirements,
select les by long pressing, and set wallpaper/copy/paste/delete. For details on other
operation, click in the upper right corner for more operation.
File Operation
56
End Meeting
Manually End Meeting
File Name
On the
Home
page, click . The
Save meeting discussion
page will be displayed.
The meeting will end and timer will stop.
The
Save meeting discussion
page displays pages, annotation page screenshots,
and remote control screenshots in the discussion mode in this meeting, as shown in the
following gure.
Picture les are named in the following of prex + creation le. Slide left/right using a
nger to switch pictures.
Prex name rule: WB (discussion mode page), AN (annotation page screenshot), and
SS (remote control screenshot).
Save Meeting Data
When no external USB ash memories are connected, icons in the
Save to
area will be
gray. When an external USB ash memory is connected, icons in the
Save to
area will
turn into blue. Click the USB icon in blue. The “uc” folder will be created under the root
folder, and the selected les will be saved in it.
57
Send E-mail
Click the button on the
Save meeting discussion
page, and click
AquaMail
to
share current meeting les by email. Before sending, conrm that an email account is
successfully set.
−
Back to meeting
: The meeting will be continued; les are not cleared and timer
continued.
−
End meeting
: The
Warning
dialog box will be displayed.
−
Click
Conrm
. All writing pages and screenshots will be deleted, and go back to
start screen page. The current meeting will be ended and the timer will reset.
−
Click
Cancel
. The meeting continues and the system stays on the
Save meeting
discussion
page.
●
Do not eject USB ash memory before completing the saving process.
●
If the USB ash memory is bigger than 16GB or the le format is not FAT32, the
data will not be saved properly.
Note
58
Automatically End Meeting
If the display is left un-operated for a specied duration, it will be locked to guarantee
your privacy. Choose
Settings > Power ON/OFF
Setting to set the duration. For details
on the setting method, see “Power ON/OFF Setting”.
After the display is locked, if it is operated again within 120 seconds, the display is
unlocked. Otherwise, the display enters the shut down mode and automatically deletes
all meeting content. After the display is unlocked, the countdown dialog box will not
appear in current meeting. The dialog box can be restored if you create a new meeting
after current meeting is complete.
59
E
Quick Setting Menu
Using two ngers to swipe up from the bottom of the screen, the quick setting menu will
then show up, as shown in the following gure.
Icon Functions
Drag the slider to adjust the brightness.
Drag the slider to adjust the volume.
Click the icon to mute/unmute.
Click the icon to turn on/off the beep sound.
Click the icon to turn on/off the blue light lter.
Click the icon to turn on/off the Smart system Wi-Fi.
Click the icon to turn on/off the audio only function.
Click the icon to turn on/off the left toolbar.
Click the icon to turn on/off the right toolbar.
Click the icon to enter the settings page.
Click the icon to return to Home page.
60
F
Serial Port Control
Connect RS-232 port to the PC or controlling product. Enable RS-232 serial port
connection and complete the following conguration.
Port: COM1 (Set according to PC or controlling product’s port number)
Baud rate 19200 Odd/even check None
Data bits 8 Stop bit 1
The following tables list controlling codes, querying codes and return.
Function Controlling codes Return codes
Power on
7F 08 99 A2 B3 C4 02 FF
01 00 CF
7F 09 99 A2 B3 C4 02 FF 01 00
01 CF
Power off
7F 08 99 A2 B3 C4 02 FF
01 01 CF
7F 09 99 A2 B3 C4 02 FF 01 01
01 CF
Mute/Unmute
7F 08 99 A2 B3 C4 02 FF
01 02 CF
7F 09 99 A2 B3 C4 02 FF 01 02
01 CF
Display status
7F 08 99 A2 B3 C4 02 FF
01 09 CF
7F 09 99 A2 B3 C4 02 FF 01 09
01 CF
HDMI front
7F 08 99 A2 B3 C4 02 FF
01 0A CF
7F 09 99 A2 B3 C4 02 FF 01 0A
01 CF
HDMI rear 1
7F 08 99 A2 B3 C4 02 FF
01 52 CF
7F 09 99 A2 B3 C4 02 FF 01 52
01 CF
HDMI rear 2
7F 08 99 A2 B3 C4 02 FF
01 53 CF
7F 09 99 A2 B3 C4 02 FF 01 53
01 CF
HDMI rear 3
7F 08 99 A2 B3 C4 02 FF
01 54 CF
7F 09 99 A2 B3 C4 02 FF 01 54
01 CF
Internal PC
7F 08 99 A2 B3 C4 02 FF
01 38 CF
7F 09 99 A2 B3 C4 02 FF 01 38
01 CF
DP
7F 08 99 A2 B3 C4 02 FF
01 56 CF
7F 09 99 A2 B3 C4 02 FF 01 56
01 CF
Page up
7F 08 99 A2 B3 C4 02 FF
01 13 CF
7F 09 99 A2 B3 C4 02 FF 01 13
01 CF
Page down
7F 08 99 A2 B3 C4 02 FF
01 14 CF
7F 09 99 A2 B3 C4 02 FF 01 14
01 CF
61
Function Controlling codes Return codes
VOL -
7F 08 99 A2 B3 C4 02 FF
01 17 CF
7F 09 99 A2 B3 C4 02 FF 01 17
01 CF
VOL +
7F 08 99 A2 B3 C4 02 FF
01 18 CF
7F 09 99 A2 B3 C4 02 FF 01 18
01 CF
Menu
7F 08 99 A2 B3 C4 02 FF
01 1B CF
7F 09 99 A2 B3 C4 02 FF 01 1B
01 CF
Home page
7F 08 99 A2 B3 C4 02 FF
01 1C CF
7F 09 99 A2 B3 C4 02 FF 01 1C
01 CF
Return (exit)
7F 08 99 A2 B3 C4 02 FF
01 1D CF
7F 09 99 A2 B3 C4 02 FF 01 1D
01 CF
OK
7F 08 99 A2 B3 C4 02 FF
01 2B CF
7F 09 99 A2 B3 C4 02 FF 01 2B
01 CF
←
7F 08 99 A2 B3 C4 02 FF
01 2C CF
7F 09 99 A2 B3 C4 02 FF 01 2C
01 CF
→
7F 08 99 A2 B3 C4 02 FF
01 2D CF
7F 09 99 A2 B3 C4 02 FF 01 2D
01 CF
↑
7F 08 99 A2 B3 C4 02 FF
01 2E CF
7F 09 99 A2 B3 C4 02 FF 01 2E
01 CF
↓
7F 08 99 A2 B3 C4 02 FF
01 2F CF
7F 09 99 A2 B3 C4 02 FF 01 2F
01 CF
Query the firmware
version number
7F 08 99 A2 B3 C4 02 FF
01 3D CF
7F 09 99 A2 B3 C4 02 FF 01 3D
01 CF
Enable the comment
function
7F 08 99 A2 B3 C4 02 FF
01 40 CF
7F 09 99 A2 B3 C4 02 FF 01 40
01 CF
Set volume
7F 08 99 A2 B3 C4 02 FF
05 XX CF
NOTE:
XX indicates the volume value (0 to
100), corresponding to hexadecimals
00 to 64.
7F 09 99 A2 B3 C4 02 FF 05 XX
01 CF
Set display mode
7F 08 99 A2 B3 C4 02 FF
06 XX CF
NOTE:
● XX = 00 indicates the Standard
mode.
● XX = 01 indicates the EnergyStar
mode.
● XX = 02 indicates the Auto mode.
7F 09 99 A2 B3 C4 02 FF 06 XX
01 CF
62
Function Controlling codes Return codes
Increase backlight
brightness
7F 08 99 A2 B3 C4 02 FF
01 47 CF
7F 09 99 A2 B3 C4 02 FF 01 47
01 CF
Decrease backlight
brightness
7F 08 99 A2 B3 C4 02 FF
01 48 CF
7F 09 99 A2 B3 C4 02 FF 01 48
01 CF
Set the value of
backlight brightness
7F 08 99 A2 B3 C4 02 FF
09 XX CF
NOTE:
XX indicates the value of backlight
brightness (0 - 100), corresponding
to the hexadecimal number system
(00 - 64).
7F 09 99 A2 B3 C4 02 FF 09 XX
01 CF
Switch backlight
7F 08 99 A2 B3 C4 02 FF
01 15 CF
7F 09 99 A2 B3 C4 02 FF 01 15
XX CF
NOTE:
● XX = 01 indicates the backlight is on.
● XX = 00 indicates the backlight is off.
Switch to child safety
lock
7F 08 99 A2 B3 C4 02 FF
01 57 CF
7F 09 99 A2 B3 C4 02 FF 01 57
01 CF
Screenshot
7F 08 99 A2 B3 C4 02 FF
01 1F CF
7F 09 99 A2 B3 C4 02 FF 01 1F
01 CF
Settings
7F 08 99 A2 B3 C4 02 FF
01 20 CF
7F 09 99 A2 B3 C4 02 FF 01 20
01 CF
63
Function Querying codes Return codes
Power supply
7F 08 99 A2 B3 C4 02 FF
01 37 CF
7F 09 99 A2 B3 C4 02 FF 01 37
XX CF
NOTE:
XX indicates the power on/off state.
● XX = 01: power on state
● XX = 00: power off state
Speaker
7F 08 99 A2 B3 C4 02 FF
01 82 CF
7F 08 99 A2 B3 C4 02 FF 01 82
XX CF
NOTE:
● 01: mute
● 00: non-mute
Current signal source
7F 08 99 A2 B3 C4 02 FF
01 50 CF
7F 09 99 A2 B3 C4 02 FF 01 50
XX CF
NOTE:
● Smart system = 30
● PC = 17
● DP = 20
● HDMI rear 1 = 1F
● HDMI Rear 2 = 1E
● HDMI Rear 3 = 18
● HDMI Front = 19
Speaker volume
7F 08 99 A2 B3 C4 02 FF
01 33 CF
7F 09 99 A2 B3 C4 02 FF 01 33
XX CF
NOTE:
XX indicates current volume value (XX is a
hexadecimal value, range: 00~64).
For example, XX = 20 indicates current
volume value is 32 (decimal value), XX = 00
indicates mute state.
D.Mode
7F 08 99 A2 B3 C4 02 FF
01 35 CF
7F 09 99 A2 B3 C4 02 FF 01 35
XX CF
NOTE:
XX indicates the mode. 00 and 01 indicate
standard and eco modes respectively.
Backlight brightness
7F 08 99 A2 B3 C4 02 FF
01 49 CF
7F 09 99 A2 B3 C4 02 FF 01 49
XX CF
NOTE:
XX indicates the value of backlight
brightness (0 - 100), corresponding to the
hexadecimal number system (00 - 64).
Backlight status
7F 08 99 A2 B3 C4 02 FF
01 81 CF
7F 08 99 A2 B3 C4 02 FF 01 81
XX CF
NOTE:
● XX = 00 indicates the backlight is on.
● XX = 01 indicates the backlight is off.
64
Function Querying codes Return codes
Switch to child safety
lock
7F 08 99 A2 B3 C4 02 FF
01 84 CF
7F 08 99 A2 B3 C4 02 FF 01 84
XX CF
NOTE:
●
XX = 01 indicates the child safety lock is on.
●
XX = 00 indicates the child safety lock is off.
Whiteboard state
7F 08 99 A2 B3 C4 02 FF
01 83 CF
7F 08 99 A2 B3 C4 02 FF 01 83
XX CF
NOTE:
●
XX = 01 indicates the whiteboard state.
●
XX = 00 indicates non-whiteboard state.
Return to system
state of the previous
9 options
7F 08 99 A2 B3 C4 02 FF
0A 00 CF
7F 08 99 A2 B3 C4 02 FF 0A 00
AB CD EF GH IJ OP QR ST UV
CF
NOTE:
● AB: Power supply
● CD: Speaker
● EF: Current signal source
● GH: Speaker volume
● IJ: D.Mode
● OP: backlight brightness
● QR: backlight state
● ST: Whiteboard state
● UV: Switch to child safety lock
65
Symptom Troubleshooting Methods
The screen cannot be powered on or
the indicator is off.
Check whether the power supply is connected.
Check whether the power supply plug is
properly connected.
Check whether the power supply line is
properly connected.
Check whether the rocker switch is enabled.
Press the reset switch and start the system
again.
The remote control is not causing a
response.
Replace the batteries.
Check whether the polarity direction of the
batteries is correct.
Use the remote control aligning with the IR
receive window. For details, see section
"Remote Control".
The image is normal but there is no
sound.
Increase volume on both the display and the
Windows system.
Check whether the display and the Windows
system are muted.
If an external computer is connected, check
whether the connection cables are normal.
During the video conference, the
remote party cannot hear the sound
of the local party.
In
Control Panel > Sound
, set the product
parameters to the default values in the
Recording
tab page.
G
FAQs & Troubleshooting
66
Symptom Troubleshooting Methods
The system is automatically powered
on/off when no operation is performed.
Disable the automatic power-on/off function.
For details, see section "Power ON/OFF
Setting".
Check whether the display entered shut down
mode due to no operation for an extended
period of time.
Check whether the input power supply is
stable.
The colors of images are abnormal.
Check whether the HDMI cable is properly
connected or has any quality issue.
The touch function is abnormal or the
positioning is inaccurate.
Restart the display.
In the Windows system, perform positioning
again. For details, see section "Positioning".
The touch function is unavailable
when the external signal source
channel is being used.
Switch between different external signal
sources.
Ensure that the USB touch cable is connected
to the proper port. For details, see section
"Ports".
Remove and insert the USB touch cable again.
There is no sound when the HDMI in
channel is used.
Remove and insert the HDMI cable again.
No image is displayed when the
HDMI out channel is used.
Generally, this issue is caused by the
compatibility of the external display product.
Replace the external display product and test
again.
The HDMI cable is too long or has a poor
quality. Replace the HDMI cable delivered with
the product.
The touch function on the front panel
is ineffective.
Touch the button using the ngertip completely.
Check whether the finger is wet or has other
liquids on it.
Restart the display.
The USB flash memory cannot be
identied.
Check whether the USB ash drive is inserted
into the correct USB port. For details, see
section "Ports".
67
Symptom Troubleshooting Methods
The conference records cannot
be saved on the USB ash drive,
and the system prompts "The
target storage product has no write
permissions."
Format the USB flash drive to the FAT32
format.
The internal PC has no signal.
Check whether the internal PC is properly
inserted in the slot.
Check whether the internal PC enters the shut
down state.
Press the power button on the internal PC (for
details, see the instructions of the internal PC),
and manually start up the internal PC.
In the Smart system or Windows
system, no wireless network can be
found or the wireless network signal
is weak.
Check whether the Wi-Fi antenna is properly
installed on the Smart system. For details, see
section "Ports".
Check whether the Wi-Fi antenna is properly
installed for the internal PC.
The keyboard is not correctly
displayed.
Confirm that the hardware keyboard is
enabled.
68
H
Specications
Model TT-6518VN TT-7518VN TT-8618VN
Display
Backlight LED
Display Area
1431.50 mm x
806.50 mm
1653.24 mm x 931.26
mm
1895.04 mm x
1065.96 mm
Active Screen
Size
65 inch 75 inch 85.60 inch
Display Ratio 16:9
Resolution 3840 horiz. by 2160 vert. Pixels, RGB stripe arrangement
Display Colors 10 bit, 1.07 billion colors
Brightness 350 nit
Contrast 1300:1
Response Time 8 ms
Life Time 50000 h (Min.)
Speaker
Speaker Position
Forward
Max. Power
Output
2 x 15 W
Electrical
Power
Consumption
Maximum ≤ 220 W
Standby Mode ≤ 0.5 W
Maximum ≤ 300 W
Standby Mode ≤ 0.5 W
Maximum ≤ 450 W
Standby Mode ≤ 0.5 W
Working Voltage AC 100 V – 240 V, 50 Hz/ 60 Hz
Touch
Touch Surface Anti-glare tempered glass
Transparency 88%
Surface
Hardness
7 H
HID support HID
69
Model TT-6518VN TT-7518VN TT-8618VN
Touch Points 10 Points
Writing Tools Eraser, Stylus or Finger
Scan Speed 250 Hz
Positioning
Accuracy
Center area 1.0 – 1.5 mm/ Edge area 1.2 – 2.0 mm
Communication
Interface
USB-A
Transportation/Storage
Storage
Temperature/
Humidity
-20 °C – 60 °C/20% RH – 80% RH(Non coagulation)
Working
Temperature/
Humidity
0 °C – 40 °C/20% RH – 80% RH(Non coagulation)
Mounting
(optional)
Wall-mounted/ Floor Stand
Outline
Dimension
1546 mm x 944 mm
x 89 mm
1771 mm x 1071 mm
x 104 mm
2018 mm x 1211
mm x 104 mm
Packing
Dimension
1720 mm x 1085 mm
x 275 mm
1918 mm x 1190 mm
x 275 mm
2155 mm x 1320
mm x 310 mm
Net Weight 39.5 kg 50.5 kg 65.0 kg
Gross Weight 55 kg 68 kg 87 kg
Ports
Front Interface
Inputs
HDMI In x 1, USB (Touch) x 1, USB (Public) x 2
Rear Interface
Inputs
HDMI In x 3, DP x 1, USB (Touch) x 4, HDMI Out x 1, DC Out (5 V,
2 A), SPDIF out x 1, Earphone out x 1, USB 2.0 (Public) x 1, USB 2.0
(Embedded) x 1, RS-232 x 1, RJ45 x 2, USB 3.0 (Public) x 1, OPS
Slots (4 K@60 Hz), Line Out x 1
Other functions
Intelligent
thermo
s
protector
Yes
Build-in WIFI 2.4 G/ 5 G (Optional)
70
Model TT-6518VN TT-7518VN TT-8618VN
Smart System
Chips ARM A53 x 41.4 GHz
RAM 2 GB
Flash 8 GB
Multimedia File
Formats
Supports all major types of multi-media les
Android Software
On Screen
Annotation
Yes
Discussion
Board
Yes
71
For more information
Please visit our website (www.newline-interactive.com) for detailed instruction manual.
Contact Us for Support
Please email us at [email protected].
I
More Information
Our company is devoted to product innovation and technology enhancement. Therefore, we may change product specs and
information without notice, Product pictures in the manual are for reference only, please refer to actual products.